Tuesday, May 22, 2012

PEMASANGAN BREAK CALIPER COVER ENDLEES(BREAK CALIPER COVER INSTALATION)



PEMASANGAN BREAK CALIPER COVER ENDLEES(BREAK CALIPER COVER INSTALATION)

Sebenarnya lama dah nak pasang benda ni,sebab brek caliper nampak kotor.Sebelum ni dah sembur cat,cat pun dah pudar.Bahagian depan pakai disc standard dan bahagian belakang pakai disc honda.( actually I wanted to do this for quite some time,, because my brake caliper look very dirty and the spray paint was faded.This is the right time to do because I find this caliper look simple and easy to install.Front I used standard break and rear disc I taken from Honda.)


PERALATAN(EQUIPMENT)

Gam silicone tahan panas(Heat resistant glue Silicone)

silicon tahan panas sehingga 600degree celcius(beli kat hardware rm6)(silicon heat resistant up to 600degree Celsius (can buy from hardware rm6)

1.cuci permukaan break caliper sehingga bersih.Rim saya tak perlu dibuka kerana cover ni boleh dimasukan di celah rim dengan mudah.Kalau tak boleh masuk kena buka lah rim anda.(Wash the surface of break caliper thoroughly.This cover can go through my rim easily.so no need to remove the rim.,If cant you have to remove it.

2.Sapukan silicon di cover dan di break caliper,lagi tebal lagi bagus.(. Apply the silicon in the cover and the break caliper, the thicker the better



3.lekatkan break cover ke break caliper,tekan dengan tangan beberapa minit sehingga ia melekat.Pastikan cover tidak tesangkut ke rim anda.Tapekan cover dan caliper dengan tape kertas supaya ia tidak jatuh,biarkan selama satu jam.Untuk mendapatkan hasil yang lebih baik biarkan ia selama 8 jam.3 (stick break cover to break caliper, press with hands a few minutes until it sticks. Make sure the cover does not touch to the rim.Tape the cover and caliper with paper tape,so it wont drop,leave it for an hour. For better results leave it for 8 hours)
lekatkan tape selama 1 jam(HOLD THE COVER WITH TAPE FOR 1 HR)


4.Dah siap inilah hasilnya(Ok all done and this is the result.)


 

PEMASANGAN NOMbor PLATE RALLYi ART FRAME

Rally art nombor plate frame
1.Buka papan nom plate,cungkil dengan screwdriver perlahan-lahan sampai plate terbuka dari plate frame yg lama.Jangan cungkil terlalu kuat kerana papan plate senang patah.







nombor plate sudah dibuka


2.Buka Nom plate frame,kalau ada screw buka saja screw tu,kalau pakai revet gunakan gerudi untuk membuka revet tersebut


frame dah dibuka

3.Ukur plate raliart pastikan ia sama tengah,gunakan marker pen untuk menandakan tempat yg hendak ditebuk

4.Pasangkan frame bahagian belakang dahulu,pastikan juga penutup yg ada tulisan rali art boleh dipasanang,barulah pasangkan screw ke body kereta.


                                              screew dah di pasang
5.lekatkan double site tape dibelakang papan noumber plate,kemudian lekatkan ke nombor plate frame,tekan supaya gam melekat dengan baik.

                                           

lekatkan dgn menggunakan double site tape


6.Akhir sekali pasang cover tulisan ralli art dan ikat skrew secukupnya....selesai


                                                                                             dah siap

Saturday, May 19, 2012

Jasma transparent timing bell cover proton 4g13/15


Jasma transparent  timing bell cover  proton 4g13/15
Brand new
Clear timing bell cover
For proton engine 4g15/4g13
Price rm45
FOR INQUIRY CALL SHOHAIME, 012-9720635,LOCATION Bandar saujana putraPUCHONG can COD atPUCHONG,USJ SUBANG ,SHAH ALAM, OR LOCATION NEAR TO MY PLACE. POS LAJU SERVICE PROVIDED IF REQUESTED
Jasma transparent  timing bell cover  proton 4g13/15
Jasma transparent  timing bell cover  proton 4g13/15
=======================================================

performance part catalogue

performance part catalogue
car performance part

LinkWithin

Related Posts with Thumbnails